username
password
send
Le cœur de la Peur et le programme des raids
Le tout nouveau donjon de raid en difficulté normale de Mists of Pandaria est maintenant ouvert : le cœur de la Peur. Le mode héroïque et l’outil Raids seront disponibles à partir du mercredi 7 novembre. ..
La Quête de la Pandarie, deuxième partie
Le deuxième chapitre de La Quête de la Pandarie est désormais disponible ! Cette nouvelle en quatre parties se déroule pendant les évènements qui surviennent entre World of Warcraft: Cataclysm et Mists of Pandaria. ..
Les caveaux Mogu’shan sont maintenant ouverts & Programme des raids
Le premier donjon de raid en difficulté normale de Mists of Pandaria est maintenant disponible : les caveaux Mogu’shan. Il sera ouvert dans l’outil Raids et en difficulté héroïque à partir du mercredi 10 octobre. ..
La Quête de la Pandarie, quatrième et dernière partie
Lisez le dernier chapitre de la Quête de la Pandarie ! Pour clore leur aventure à travers Azeroth, nos intrépides héros se retrouvent pris dans le conflit latent entre la Horde et l’Alliance. ..
headlines

Plastic electronic appliances factory< Sujet précédent  Sujet suivant >
Index du Forum -> Categorie 1 -> Forum
AuteurMessage
France.gif astao269
Junior Member


Messages : 10
Inscrit(e) le: 27/03/2020
Posté le 27-03-2020 02:18  
Plastic electronic appliances factory
abs injection molding
Product Description                                                                                                                                       
4) The density of different parts is different. The final result of shrinkage, the density of each part is different. The density of the central part or the thick glue position is small, and the density of the frozen layer is relatively large.
5) Reasons for shrinkage-concavity: When abs injection molding product cools and shrinks, the frozen layer is cooled first, forming a hard shell surrounded, which has a fast cooling rate, a small-shrinkage and a high density; and the center or thick glue The location temp is high, the cooling rate is slow, the density is low, and the amount of shrinkage-is large. Since the cooling of the central portion or the thick glue position lags behind the frozen layer, when these portions are cooled and contracted, they are not able to shrink-freely, and are restricted by the peripheral frozen layer. When the thickness of the frozen layer is large and the resistance to deformation is strong, when the shrinkage force of the thick glue position of the-product is smaller than the deformation resistance of the frozen layer, hollow bubbles are generated; when the thickness of the frozen layer is thin and the resistance to deformation is poor, When the-shrinkage force of the thick glue position is greater than the deformation resistance, the skin is pulled inward to form a shrinkage concavity limit.
There are many reasons for the shrinkage-concavity, and the solutions are different.
First, choose a plastic raw material with a small shrinkage-rate.
For raw materials of the same nature, the shrinkage-rates of different grades are different. It is necessary to select raw materials with small shrinkage as much as possible. Crystalline plastics shrink-more than amorphous plastics.
The cooling conditions are different, and the thickness of the frozen layer of the product is different. The thickness of the frozen layer is different, and the ability to resist shrinkage-deformation is different. Sometimes the temp of the front mold is lowered, and the temp of the rear-mold is increased, so that the frozen layer of the-product surface becomes thicker, the thickness of the frozen layer on the reverse side becomes thinner, and when the thick glue position-shrinks, the reverse side is concave, and the surface of abs injection molding does not have a depression.
The change and effect are also contradictory. The high mold-temperature is conducive to the flow of the melt, which is-conducive to compression and feeding; but the-mold-temperature-is-high, the cavity size is large, the-melt-temperature is-high, and the-shrinkage-rate is-increased.
Our Company                                                                                                                                            


Our Service                                                                                                                                             It is not known that changing the thickness of the frozen layer can change the direction of the shrinkage dents, and is rarely used.
Fourth, change the structure design. Change the structural design of the product so that it is as uniform as possible. For the-mold that has been completed, it can be discussed with structure designer to solve the problem of partial reduction.
abs injection molding Certifications                                                                                                         

Customers Photo                                                                                                                                     
Favrable Comment
FAQ                                                                                                                                                                   
Why Choose Julier                                                                                                                                        
Plastic electronic appliances factory
website:http://www.custom-plastic-mold.com/plastic-injection-molding/home-appliances-plastic-parts/


Revenir en haut | Permalien

Generated in 0.221923s